Eagle: Difference between revisions

From Fab Lab Wiki - by NMÍ Kvikan
Jump to navigation Jump to search
← Older editNewer edit →
Line 33: Line 33:
*'''Delete''' to remove object or line and so on.
*'''Delete''' to remove object or line and so on.
*'''Junction''' Connection point .
*'''Junction''' Connection point .
**You can right click objects and select '''value''' to put
**You can right click objects and select '''value''' to set values e.g. for capacitors or resistors
**Right click on object and select '''properties''' to rename.
**You can check out if you have connected the object by moving them.


**hægt að hægri smella á hluti og velja '''value''' til að setja inn gildi s.s. fyrir þétta.
*'''ERC''' Error correction, search for errors.
**hægri smella og velja '''properties''' til að endurnefna.
===Arrange objects ===
* Til að athuga hvort hlutur sé rétt tengdur er gott að prófa að hreyfa hlutinn.
 
*'''ERC''' Error correction villuleit.
===Raða hlutum upp ===
Add  
Add  
*'''Frame''' til að setja ramma utan um teikninguna.
*'''Frame''' to make frame around the design.
*Arrange objects
*click '''Auto'''
**Select Bottom N/A


*raða hlutum
If it is not as good as you wanted you can select lines, by right clicking them and select '''rip off'''
*smella á '''Auto'''
**Velja Bottom N/A


Ef þetta raðast ekki rétt
hægt að velja línur með þvi hægri smella og velja '''rip off'''




==Info about Circuits==
*TX transmit
*TX transmit
*DTR data terminal ready
*DTR data terminal ready

Revision as of 13:46, 7 March 2011

See version in Icelandic eagle kennsluefni

Download and install Eagle

Designing circuits with Eagle

Open Eagle

  • Select New Project
  • Select New Schematic

Open library

  • Open library, click Use
  • Download from the internet a library or select on in the computer the library that we will be using (e.g. NG.lbr[1] or the one from Sparkfun.lbr ([2] version 2011 ( right click on this link, save link as)
  • SelectAdd, then you can open the library
    • (if you don't find your thing you could also click on "Use")
  • Open NG.lib library for Fab Lab projects.


Tour for the Eagle on CadSoft site


  • Select the things you want to use and click Add to get the components.
  • You can select different view by clicking on Board
  • You can select object by rightclicking them and selecting packning
  • Connect objecs by clicking Wire and make wire between objects.
  • It can be good to make connections and get a sign for Ground and put where it should be GND.
  • View Grid select the size of the grid, it should be around (0,025 inches)
  • Move to move object or line.
  • Delete to remove object or line and so on.
  • Junction Connection point .
    • You can right click objects and select value to set values e.g. for capacitors or resistors
    • Right click on object and select properties to rename.
    • You can check out if you have connected the object by moving them.
  • ERC Error correction, search for errors.

Arrange objects

Add

  • Frame to make frame around the design.
  • Arrange objects
  • click Auto
    • Select Bottom N/A

If it is not as good as you wanted you can select lines, by right clicking them and select rip off


Info about Circuits

  • TX transmit
  • DTR data terminal ready
  • Rx Recieve
  • Miso -master in slave out
  • Mosi master out slave in
  • sck system clock
  • MOSI (3) GND (2) MISO (1) |
  • -RESET (4) SCK (5)

Project 1

First project could be to make schematic of this board and to add something to it, add (at least) a button and LED (with current-limiting resistor) to the serial echo hello-world board, check the design rules, and make it

Materials used

  • IC1 = ATtiny44_SOIC('IC1\nt44')
  • R1 = R_1206('R1\n10k')
  • C1 = C_1206('C1\n1uF')
  • XTAL = Crystal 20 MHz
  • FTDI connector (6 pin)
  • Header (2*3 pin)

Links

Retrieved from "https://wiki.fablab.is/index.php?title=Eagle&oldid=7504"