Difference between revisions of "Rhino námskeið"
From Fab Lab Wiki - by NMÍ Kvikan
(5 intermediate revisions by the same user not shown) | |||
Line 14: | Line 14: | ||
*[http://fireflyexperiments.com/download/ http://www.rhino3d.com/download/rhino/5.0/latest] | *[http://fireflyexperiments.com/download/ http://www.rhino3d.com/download/rhino/5.0/latest] | ||
− | == | + | ==Tenglar== |
*[http://natureofcode.com/ Nature of Code http://www.rhino3d.com/download/rhino/5.0/latest] | *[http://natureofcode.com/ Nature of Code http://www.rhino3d.com/download/rhino/5.0/latest] | ||
+ | *[http://digitaltoolbox.info/ http://digitaltoolbox.info/] | ||
+ | *[http://www.grasshopper3d.com/ http://www.grasshopper3d.com/ ath td. PRIMER] | ||
+ | *[http://www.food4rhino.com/ http://www.food4rhino.com/] | ||
+ | *Ath Arduino | ||
+ | **VirtualColorMixer | ||
+ | **http://arduino.cc/en/Tutorial/HomePage | ||
+ | |||
+ | |||
+ | Firefly | ||
+ | *[http://vimeo.com/35973354 http://vimeo.com/35973354] | ||
+ | |||
+ | |||
+ | ==Viðbætur á Grasshopper | ||
+ | *Firefly | ||
+ | *Kangaroo Physics | ||
+ | |||
+ | |||
+ | |||
+ | ==Minnispunktar== | ||
+ | ===Rhino=== | ||
+ | teikna prófíl | ||
+ | |||
+ | *sweep1 | ||
+ | **til að búa til rail | ||
+ | **stefna velja endapunkta á railinu | ||
+ | *cap | ||
+ | **muna að setja tappa á það sem maður hefur gert | ||
+ | |||
+ | fyrir 3d prentun | ||
+ | *surface- edge tools -show edges (til að sjá s.k. naked edges) ef formið er ekki lokað. | ||
+ | **modelið þarf að vera laust við naked edges til þess að hægt sé að 3d prenta hlutinn. | ||
+ | |||
+ | |||
+ | ===Grasshopper=== | ||
+ | *Display -> Draw Icons | ||
+ | *CTRL Q | ||
+ | |||
+ | *set one surface | ||
+ | *rebuild |
Latest revision as of 16:31, 20 October 2013
Rhino námskeið
Hlaðið niður Rhino3D evaluation nýjustu útgáfu
Grasshopper 3d nýjustu útgáfu
Arduino nýjustu:
Firefly nýjustu:
Contents
Tenglar
- Nature of Code http://www.rhino3d.com/download/rhino/5.0/latest
- http://digitaltoolbox.info/
- http://www.grasshopper3d.com/ ath td. PRIMER
- http://www.food4rhino.com/
- Ath Arduino
- VirtualColorMixer
- http://arduino.cc/en/Tutorial/HomePage
Firefly
==Viðbætur á Grasshopper
- Firefly
- Kangaroo Physics
Minnispunktar
Rhino
teikna prófíl
- sweep1
- til að búa til rail
- stefna velja endapunkta á railinu
- cap
- muna að setja tappa á það sem maður hefur gert
fyrir 3d prentun
- surface- edge tools -show edges (til að sjá s.k. naked edges) ef formið er ekki lokað.
- modelið þarf að vera laust við naked edges til þess að hægt sé að 3d prenta hlutinn.
Grasshopper
- Display -> Draw Icons
- CTRL Q
- set one surface
- rebuild